Toyota Corolla

1992-1998 of release

Repair and car operation



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
- 11. Body
   11.1. Maintenance and repair
   11.2. Vinyl furnish
   11.3. Upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of considerable damages of a body
   11.6. Loops and locks
   11.7. Windscreen and motionless glasses
   11.8. Cowl
   11.9. Trunk lid
   11.10. A back door (models with a body "Versatile person")
   11.11. Basic rack of a back door
   11.12. Decorative panel of a door
   11.13. Door
   11.14. Door latch, lock and handle cylinder
   11.15. Door windowpane
   11.16. Bumpers
   11.17. External mirror
   11.18. Seats
   11.19. Frame of a combination of devices
   11.20. Glove compartment
   11.21. Central decorative panel
   11.22. Casing of a steering column
   11.23. Bottom panel of furnish of a steering column
   11.24. Console
   11.25. Dashboard
   11.26. Front grille
   11.27. Ventilating lattice of a cowl
   11.28. Seat belts
+ 12. Electric equipment


buy viagra pills 100 mg online

11.12. Decorative panel of a door

Removal

PERFORMANCE ORDER
1. Disconnect a "weight" wire from the accumulator.
Prevention

If the speaker system in your car is equipped with anticreeping system, be convinced that you know the correct activation code before disconnecting the accumulator.


2. On the models equipped with glasses with a manual drive, remove the handle of a window regulator, feats forward-back a fabric behind the handle while the clamp (it is specified by an arrow) will not be put forward so that it could be removed. For carrying out this procedure there is a special adaptation, however, it is possible to manage and without it.
4. Having unfastened a clamp, pull out the handle. On the models equipped with an electric drive of a window regulator, take switch knot, disconnect the electric socket and remove it.
5. Remove a decorative covering of an external mirror (see subsection 11.17).
6. Remove the internal handle of a door (see subsection 11.14).
7. By means of a screw-driver raise an armrest.
8. Unscrew fixing screws of decorative furnish of a door and remove an armrest.
9. Insert a wide shpatel, a thin screw-driver or the special adaptation for removal of decorative furnish of a door between furnish and a door to disconnect fixing clips. Do this operation on all external edge to unfasten the panel.
10. When all clips will be disconnected, unfasten decorative furnish of a door, disconnect all electric connections and remove the decorative panel from the car, having carefully pulled it up.
11. To get access to an inside door, remove the plastic guard protecting a door from hit of moisture. Remove a plastic covering, trying not to tear it. Remove plastic condensing rings if it is necessary.

Installation

PERFORMANCE ORDER
1. To establish the decorative panel, first of all, establish into place a guard warning a door from hit of moisture. If it is necessary, add more hermetic to fix it on a place.
2. Before installation of the panel of a door be convinced that all clips in panel which could jump out during removal or remain at doors, are established.
3. Connect all electric connections and place the panel into place. Press on it to fix clips, and establish all fixing screws and door a handle / armrest. Establish the handle of a manual window regulator or the electrowindow regulator switch.