Toyota Corolla

1992-1998 of release

Repair and car operation



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
- 9. Brake system
   9.1. Specifications
   9.2. System of anti-blocking of brakes (ABS)
   9.3. Brake shoes of forward brakes
   9.4. Support of forward brakes
   9.5. Brake shoes of back disk brakes
   9.6. Support of back disk brakes
   9.7. Brake disk
   9.8. Brake shoes of back drum-type brakes
   9.9. Working cylinder
   9.10. Main cylinder of brake system
   9.11. Brake hoses and tubes
   9.12. Hydraulic system of brakes
   9.13. Vacuum amplifier
   9.14. Hand brake
   9.15. Ropes of the hand brake
   9.16. Brake pedal
   9.17. Switch of headlights of a stoplight
   9.18. The valve of restriction of the pressure, sensitive to car loading
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment


9.15. Ropes of the hand brake

Replacement

PERFORMANCE ORDER
Ropes between the equalizer and brakes
1. Turn off nuts of fastening of back wheels, lift a back part of the car and establish it on support. Block forward wheels. Remove a back wheel.
2. Check, that the car did not stand on the hand brake, then, on drum-type brakes, remove a brake drum.
3. On models with drum-type brakes remove brake shoes and disconnect a rope from the lever of the hand brake (see subsection 9.8). Turn off two fixing bolts (are specified by shooters) a rope on a guard of a back brake and pull out a rope through an opening in a guard.
4. On models with disk brakes disconnect a rope from a support, having got the check and a pin, at the same time pressing the cranked lever of the hand brake. Remove a fixing clip of a braid of a rope and remove a rope.
5. Turn off a fixing nut of a clip near forward fastening of longitudinal draft.
6. Turn off a bolt (it is specified by an arrow) fastenings of a clip of a rope to the floor panel.
7. Remove thermal screens of an exhaust pipe and the catalytic converter (see subsection 6.9).
8. Turn off fixing bolts of clips (are specified by the right shooters). Get nylon plugs from arms (are specified by the central shooters). Disconnect the forward ends of ropes from the equalizer (it is specified by the left shooters).
9. Installation is carried out upside-down removals. Apply a thin film high-temperature greasing for the end of a rope which fastens to the equalizer.
10. Adjust the hand brake after completion of installation of a rope (see subsection 9.14).
Rope between the equalizer and the lever of the hand brake
11. Remove the central console (see subsection 11.24).
12. When the lever is lowered, turn off a lock-nut and an adjusting nut (see subsection 9.14) and disconnect a rope from the lever.
13. Lift a back part of the car and establish it on support.
14. Remove thermal screens of an exhaust pipe and the catalytic converter (see subsection 6.9).
15. Turn the rope end on 90 ° and disconnect it from the equalizer.
16. Get the rubber plug from the panel of a floor and get a rope through an opening in the panel.
17. Installation is carried out upside-down removals. Apply a thin film high-temperature greasing on a site of a rope which fastens to the equalizer. Also cover edges of the rubber plug with silicone glue in order that it did not pass water.

18. Adjust a course of the lever of the hand brake on termination of installation (see subsection 9.14).