Toyota Corolla
+ 1. Maintenance instruction
- 2. Maintenance
2.1. Specifications
2.2. Arrangement of knots and details
2.3. Check of level of liquids
2.4. Check of a condition of tires and pressure in tires
+ 2.5. Servicing through each 5000 km or 3 months
+ 2.6. Servicing through each 12000 km or 6 months
+ 2.7. Servicing through each 24000 km or 12 months
- 2.8. Servicing through each 50000 km or 2 years
2.8.1. Replacement of the fuel filter
2.8.2. Check of a condition and replacement of spark plugs
2.8.3. High-voltage wires, cover of the distributor and rotor begunok
2.8.4. Service of system of cooling
2.8.5. Check of system of catching паров gasoline
2.8.6. Check of an exhaust system
2.8.7. Replacement of oil, transmission liquid and filter
2.8.8. Oil replacement in a manual transmission case
2.8.9. Zolotnik and hose of system of compulsory ventilation of a case
+ 2.9. Servicing through each 100000 km or 4 years
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment
|
Set of tools for replacement of spark plugs
|
1. A candle face natural a rubber insert for protection of a porcelain insulator
2. Dinamometrichesky key. It is intended for
inhalings of candles (though
its application is unessential)
3. Graggers. It is intended for a wraparound and a candle inhaling
|
4. Adapter. It is intended for assembly of connection and for an otvorvchivaniye of candles in engines of different types. Depending on the car and available tools adapters of various types (including the extension piece with the kardanny hinge) are used
5. Set of calibres. It is intended for gap check between candle electrodes, has various executions. Be convinced that the set includes the calibre suitable for a candle of your car
|
For replacement of candles the candle face natural is required by a graggers. The face head candle a candle is supplied with a rubber insert not to damage a porcelain insulator of a candle, and also for candle deduction at installation in a head of the block of cylinders. Also the calibre of round section for check and gap adjustment between candle electrodes, and a dinamometrichesky key for a candle inhaling (see fig. is required. A set of tools for replacement of spark plugs).
Set of calibres. It is intended for gap check between candle electrodes, has various executions. Be convinced that the set includes the calibre suitable for candles of your car
At replacement of candles it is necessary to get new candles, to expose a gap and to screw instead of old, replacing each candle separately
Prevention
Getting new candles, be convinced that their type corresponds to your car. The type of a candle is specified in the section "General specifications", in the information plate from a reverse side of a cowl (VECI-to the plate on which standards of emissions in the atmosphere for your car), and also in the car maintenance instruction are also specified. If data of the specified sources differ, be guided by data of the information plate as type of candles specified in the plate corresponds to type of the engine of your car.
| PERFORMANCE ORDER |
| 1. Check a condition of new candles. At detection of any signs of damages of an insulator of a candle it is impossible to establish. |
|
2. Check a gap between electrodes of new candles. The calibre of round section is for this purpose used. The calibre should move between electrodes under small effort, gap adjustment otherwise is required. |
|
3. The gap between electrodes should correspond specified in subsection 2.1 or in the information plate from a reverse side of a cowl. If the gap does not correspond to norm, turn in an electrode by means of the lever on the case of a set of calibres, thus do not damage a porcelain insulator round the central electrode. |
| 4. If the lateral electrode does not coincide with central, turn in the lever on the case of a set of calibres before combination of both electrodes on the candle center. |
Prevention
At exposure of a gap to turn in only a lateral electrode.
|
|
Removal
| PERFORMANCE ORDER |
|
1. Not to mix high-voltage wires replace each candle separately. Remove from a candle a high-voltage wire and a tip, holding a tip, but not for a wire. Turn a tip on a half of turn, at the same time making the effort directed up, and get a wire. |
| 2. In the presence of the compressed air blow places round a candle, having removed dirt (it is possible to use and the bicycle pump). |
|
3. Turn out a candle. Turn on I shine with a special face natural the extension piece. |
| 4 whether. Irrespective of the candle will change, or to be turned old, check a candle condition according to the nomogram and define the general condition of the engine. |
|
Installation
| PERFORMANCE ORDER |
|
1. Before a wraparound of a candle it is into place recommended to grease a carving with fixing structure. Usually difficult happens to wrap a candle without distortions. |
|
2. To avoid a distortion dress on a candle a hose piece with internal diameter 3/8 inches (9,5 mm). The manipulation a flexible hose facilitates the correct installation of a candle at a wraparound. As soon as the candle will start to be wrapped with a distortion a hose will start to be scrolled on an insulator owing to what carving damage is prevented. Tighten a candle with the set moment (see subsection 2.1). |
| 3. Establish a tip, having turned on a half of turn and having at the same time made the effort directed down, against the stop in a candle electrode. |
| 4. Replace other candles, having repeated the procedure described above. |
|
|
|