Toyota Corolla

1992-1998 of release

Repair and car operation



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
- 12. Electric equipment
   12.1. Safety locks
   12.2. Burned-through crossing points
   12.3. Automatic switches
   12.4. Relay
   12.5. Breakers of indexes of turns / alarm system
   12.6. The combined switch
   12.7. The switches established on a steering column
   12.8. Lock of ignition and lock drum
   12.9. Switch of a heater of back glass
   12.10. Heater of back glass
   12.11. Radio receiver and loudspeakers
   12.12. Aerial
   12.13. Bulbs of headlights of head light
   12.14. Headlights of head light
   12.15. Replacement of bulbs
   12.16. System of day inclusion of headlights
   12.17. Engine of screen wipers
   12.18. Instrument guard
   12.19. Sound signal
   12.20. System cruise control
   12.21. System of the central lock
   12.22. System of window regulators
   12.23. Rear-view mirrors with the electric drive
   12.24. Safety airbag
   + 12.25. Electroschemes



12.10. Heater of back glass

GENERAL INFORMATION

The heater of back glass consists of a certain number of the horizontal heating elements which have been soldered in in a surface of back glass.

It is possible to eliminate small ruptures of elements, without removing back glass.

Check

PERFORMANCE ORDER
1. Turn a key in the lock of ignition and the switch of a heater of back glass in the situation On.
2. At tension measurement in the following two tests, wrap up a strip of an aluminum foil around щупа a negative wire of the voltmeter and press a foil to a wire a finger (1–щуп the voltmeter, 2 – a wire of a lattice of a heater, 3 – a foil).
3. Check tension in the middle of each of heating wires. If tension is equal to 5 volts, the wire in an order (the gap is not present) means; if tension is equal to 10 volts, the wire means is broken off in a point somewhere in between the center of a wire and the positive plug; if tension is equal to 0 volts, means, the wire is torn between the center of a wire and weight
4. Connect negative щуп the voltmeter to mass of the car. Indications should remain same.
5. For detection of a point of a gap connect positive щуп the voltmeter to the positive plug of a lattice of a heater, concern with a foil in which will wrap up negative щуп, to a wire of a lattice of a heater as it is possible closer to the positive plug and carry out a foil with negative shchupy on a wire towards the negative plug. The point in which indications of the voltmeter will rise from zero to several volts, is a point in which the wire is torn.
6. If the heating element is not torn, the voltmeter will show lack of tension on a positive ring of a wire, and will show all increasing tension at approach by the negative end where it will be approximately equal 12 volts.

Repair


PERFORMANCE ORDER
1. Eliminate a rupture of a wire, using the repair set which has been specially developed for this purpose which can be got on a car market or in autoshop.
2. Before the repair beginning, switch off a heater and wait, while it will cool down within several minutes.
3. Smooth out gap area a small emery paper a little, then carefully it clear alcohol.
4. By means of a sticky tape designate gap area.
5. Eliminate a rupture of a wire, being guided by the instructions attached to a repair set.