Toyota Corolla

1992-1998 of release

Repair and car operation



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
- 12. Electric equipment
   12.1. Safety locks
   12.2. Burned-through crossing points
   12.3. Automatic switches
   12.4. Relay
   12.5. Breakers of indexes of turns / alarm system
   12.6. The combined switch
   12.7. The switches established on a steering column
   12.8. Lock of ignition and lock drum
   12.9. Switch of a heater of back glass
   12.10. Heater of back glass
   12.11. Radio receiver and loudspeakers
   12.12. Aerial
   12.13. Bulbs of headlights of head light
   12.14. Headlights of head light
   12.15. Replacement of bulbs
   12.16. System of day inclusion of headlights
   12.17. Engine of screen wipers
   12.18. Instrument guard
   12.19. Sound signal
   12.20. System cruise control
   12.21. System of the central lock
   12.22. System of window regulators
   12.23. Rear-view mirrors with the electric drive
   12.24. Safety airbag
   + 12.25. Electroschemes


12.15. Replacement of bulbs

GENERAL INFORMATION

Clips of the panel of furnish of a luggage carrier

1. Removal


2. Installation

FORWARD LAY HEADLIGHTS AND LATERAL INDEXES OF TURNS

PERFORMANCE ORDER
1. Turn off the fixing screw (it is specified by an arrow) and remove a headlight, having pushed it forward (in the arrow direction).
2. Disconnect the socket of connection and turn cartridges with bulbs counter-clockwise for replacement of bulbs.

INDEXES OF TURNS

PERFORMANCE ORDER
1. Turn off fixing screws and get a headlight from a bumper, having turned it.
2. Disconnect the socket of connection and turn a cartridge with a bulb counter-clockwise for its removal.

BULBS OF BACK LATERAL INDEXES OF TURNS, HEADLIGHTS OF THE STOPLIGHT, BACK INDEXES OF TURNS, DIMENSIONAL HEADLIGHTS AND BACKING HEADLIGHTS

PERFORMANCE ORDER
On models with the Sedan type body
1. Turn off two screws, fixing a block headlight, open a luggage carrier and remove the furnish panel for receiving access, then turn off a nut and get a back block headlight.
2. Turn cartridges of bulbs counter-clockwise, get them and replace bulbs.
On models with the Versatile person type body
3. Turn off the fixing screw and lift a block headlight up for its removal.
4. Turn cartridges of bulbs counter-clockwise, get them and replace bulbs.

BULBS OF ILLUMINATION OF REGISTRATION PLATE

PERFORMANCE ORDER
On models with a Cедан type body
1. Press on a uvula and lower a rasseivatel of a lamp down for receiving access to a bulb.
2. Turn a cartridge of a bulb counter-clockwise and remove it.
On models with the Versatile person type body
3. Turn off screws of fastening of a lamp of illumination of registration plate and lower a lamp.
4. Remove the holder of a bulb, having turned it counter-clockwise, then get from the boss a bulb.

THE LAMP OF THE STOPLIGHT LOCATED ON THE CEILING OF SALON BEFORE BACK GLASS

PERFORMANCE ORDER
On models with a Cедан type body
1. By means of a ball pen press on the center of fastenings, and then remove fastenings by means of a screw-driver and remove a headlight casing.
2. Turn off bolts of fastening of a lamp, lift a lamp for receiving access, then turn a cartridge with a bulb counter-clockwise for its removal and get a bulb, having simply pulled it on itself.
On models with the Versatile person type body
3. Remove a rasseivatel of a bulb, remove the holder of a bulb, having turned it counter-clockwise, then get a bulb from the boss.

BULBS OF ILLUMINATION OF SALON

PERFORMANCE ORDER
1. By means of a small screw-driver remove rasseivatel.
2. Get a bulb from contacts. Probably, you should hook a bulb a screw-driver, in this case, hook bulb edge (differently glass can burst).

BULBS OF ILLUMINATION OF THE INSTRUMENT GUARD

PERFORMANCE ORDER

1. For receiving access to bulbs of illumination of an instrument guard, it is necessary for removing (see subsection 12.18).

2. Accurately take a bulb clip aside (it is specified by an arrow) and get a bulb. It is possible to establish bulbs behind an instrument guard.