Toyota Corolla

1992-1998 of release

Repair and car operation

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
- 12. Electric equipment
   12.1. Safety locks
   12.2. Burned-through crossing points
   12.3. Automatic switches
   12.4. Relay
   12.5. Breakers of indexes of turns / alarm system
   12.6. The combined switch
   12.7. The switches established on a steering column
   12.8. Lock of ignition and lock drum
   12.9. Switch of a heater of back glass
   12.10. Heater of back glass
   12.11. Radio receiver and loudspeakers
   12.12. Aerial
   12.13. Bulbs of headlights of head light
   12.14. Headlights of head light
   12.15. Replacement of bulbs
   12.16. System of day inclusion of headlights
   12.17. Engine of screen wipers
   12.18. Instrument guard
   12.19. Sound signal
   12.20. System cruise control
   12.21. System of the central lock
   12.22. System of window regulators
   12.23. Rear-view mirrors with the electric drive
   12.24. Safety airbag
   + 12.25. Electroschemes

12.21. System of the central lock

GENERAL INFORMATION

Arrangement of elements of system of the central lock

1. Block of safety locks of N2 (AM1 Safety lock)
2. Ignition lock
(Switch of an alarm bulb)
3. Control relay of locks of doors

4. Block of safety locks of N1 (Window regulator safety lock) (Safety lock of an instrument guard)
5. Switch of locks
6. Locks of doors (The lock engine) (The control switch checking closing of the lock)

The system of the central lock puts in action drives of locks of doors which are located in each of doors.

The system consists of switches, drives and connecting wires.

Diagnostics is usually limited to check of connections of wires and drives on existence of small malfunctions which it is easy to eliminate.

Table of connection of a tester and conductivity of the main block of switches of system of the central lock

Table of connection of a tester and conductivity of the switch of the lock

1. It is closed

2. It is unlocked

3. Before

Check

PERFORMANCE ORDER

1. The system of the central lock uses bilateral solenoids for short circuit and an otmykaniye of locks of doors. Switches of locks have two working conditions: (Lock) is closed and (Unlock) Is open. These switches put in action the relay which in turn submits tension on solenoids of locks of doors. Depending on what signal is sent on the relay, it changes the polarity, allowing both parts of a chain to have positive or negative tension.

2. Always, first of all, check protection of an electric chain. On some cars automatic switches and safety locks are used together.

3. Switch switches in both situation (Lock and Unlock) at the switched-off engine. Listen to weak click of the working relay.

4. If you do not hear click, check tension presence on switches. If tension is present, check wires between the block of safety locks and switches on existence of short circuits or gaps.

5. If tension is present, but click is not audible, check the switch on conductivity of a current. Replace the switch if he does not carry out a current in one of provisions (see tab. Table of connection of a tester and conductivity of the main block of switches of system of the central lock).

6. If the switch carries out a current, but the relay does not click, check wires between the switch and the relay. Restore connection if in a chain there is a gap.

7. If the relay receives a food from the switch, but does not send it on solenoids, check reliability of grounding of the case of the relay. If grounding of the case of the relay as it should be, replace the relay.

8. If solenoids of all locks, except one work, remove the furnish panel from that door (see subsection 11.12) and check tension existence on the solenoid at turning on / switching off of the switch of the lock. On one of wires there should be a tension when the switch is in situation is closed; the second wire should be energized when the switch is in situation is unlocked.

9. If on the idle solenoid there is a tension, replace it.

10. If on the idle solenoid there is no tension, check a wire between the solenoid and the relay on gap existence.

Prevention

Often wires break in that part of a plait of wires which is located between a body and a door (continuous opening and closing of a door leads to accumulation in wires of fatigue and, finally, to a rupture of wires).