Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
- 3.1. Petrol engines
- 3.1.1. Repair work without engine dismantle from the car
3.1.1.1. Specifications
3.1.1.2. Installation of the piston of the 1st cylinder in MWT of a step of compression
3.1.1.3. Cover of a head of the block of cylinders
3.1.1.4. A soaking-up collector
3.1.1.5. Final collector
3.1.1.6. Gear belt
3.1.1.7. Forward epiploon of the crankshaft
3.1.1.8. Cam-shaft epiploon
3.1.1.9. Cam-shafts and pushers (engines of 1,3 l)
3.1.1.10. Cam-shafts and pushers (l engines 1,6 and 1,8)
3.1.1.11. Head of the block of cylinders
3.1.1.12. Oil pallet
3.1.1.13. Oil pump
3.1.1.14. Flywheel (or leading disk of the hydrotransformer)
3.1.1.15. Back epiploon of the crankshaft
3.1.1.16. Engine mount details
+ 3.1.2. Dismantle and major maintenance
+ 3.2. Diesel engine
+ 3.3. Engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment
|
Removal
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
Prevention
If the stereoradio tape recorder of the car is equipped with security system, before a battery detachment from weight be convinced that you know an activation code.
|
| 2. Disconnect hoses of system of compulsory ventilation of a case from a cover of a head of cylinders. |
| 3. Disconnect from spark plugs high-voltage wires, undertaking isolating tips, instead of for wires. |
|
|
4. On engines 1,6 and 1,8 of l unscrew two bolts of a cover of a head of the block of cylinders from a gear belt, get a cover of plaits of conducting and conducting. |
|
|
5. Unscrew nuts of fastening of a cover (are specified by shooters), uncover heads of cylinders and laying. (On engines of 1,3 l in a forward part there is an additional nut.) If the cover does not give in, in hammer blows through wooden laying loosen a cover. If this reception does not help, between a head of cylinders and a cover enter a flexible shpatel and open consolidation. |
Prevention
It is not allowed to separate with force a cover from a head of cylinders, hooking the tool as it is possible to damage surfaces of a prileganiye of these details that will lead to an oil leak after assembly.
|
|
Installation
| PERFORMANCE ORDER |
|
1. Before installation carefully clear contact surfaces of a head of cylinders and a cover. In the absence of hardenings or cracks, and also at small run rubber laying can be not changed. Before installation of a cover of a head of cylinders be convinced available sealants of plugs of spark plugs from the interior of a cover. |
| 2. Remove laying and wash out condensed surfaces solvent of varnishes or acetone. Establish new laying, having evenly pressed it on a cover contour into a flute. Existence on condensed surfaces of oil pollution at assembly can be at the bottom of an oil leak from under laying. |
| 3. Put RTV hermetic on condensed places near a rubber cap, the distributor of ignition and a cover of an epiploon of a cam-shaft. |
| 4. Establish a cover, wrap nuts. |
| 5. Evenly tighten nuts in three-four receptions of c by the set moment. |
| 6. Establish other details, start the engine and check existence of a leak of oil. |
|
|
|