Toyota Corolla

1992-1998 of release

Repair and car operation



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. Petrol engines
      - 3.1.1. Repair work without engine dismantle from the car
         3.1.1.1. Specifications
         3.1.1.2. Installation of the piston of the 1st cylinder in MWT of a step of compression
         3.1.1.3. Cover of a head of the block of cylinders
         3.1.1.4. A soaking-up collector
         3.1.1.5. Final collector
         3.1.1.6. Gear belt
         3.1.1.7. Forward epiploon of the crankshaft
         3.1.1.8. Cam-shaft epiploon
         3.1.1.9. Cam-shafts and pushers (engines of 1,3 l)
         3.1.1.10. Cam-shafts and pushers (l engines 1,6 and 1,8)
         3.1.1.11. Head of the block of cylinders
         3.1.1.12. Oil pallet
         3.1.1.13. Oil pump
         3.1.1.14. Flywheel (or leading disk of the hydrotransformer)
         3.1.1.15. Back epiploon of the crankshaft
         3.1.1.16. Engine mount details
      + 3.1.2. Dismantle and major maintenance
   + 3.2. Diesel engine
   + 3.3. Engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment



3.1.1.14. Flywheel (or leading disk of the hydrotransformer)

Removal

PERFORMANCE ORDER
1. Lift the car and establish on supports, then remove transmission (check point), being guided by the description in subsection 7.1.5 and subsection 7.2.8.
2. On the cars equipped with a manual transmission, remove the coupling mechanism in collecting (see subsection 8.2.1).
3. Put with paint or накерните labels (are specified by shooters) to mutual orientation of a flywheel and the crankshaft to provide the correct installation of a flywheel at assembly.
4. Unscrew bolts of fastening of a flywheel (a leading disk of the hydrotransformer) to the crankshaft. Having rested a screw-driver against a gear wreath, fix a flywheel from a provorachivaniye.
5. Remove a flywheel (a leading disk of the hydrotransformer) from the crankshaft. A flywheel quite heavy detail therefore, at a reversing of the last bolt hold a flywheel.

6. On some cars equipped with automatic transmission, on both parties of a leading disk remote washers are established. Pay attention to the provision of an adjusting pin (it is specified by an arrow). Store washers together with a disk.

Prevention

Work in gloves not to wound a hand about sharp teeths of a flywheel.



Installation

PERFORMANCE ORDER
1. Clear a flywheel, remove the greasing remains. Check existence on a surface of traces of deep development, furrows from rivets, traces of burning out and scratches. Insignificant damages can be liquidated cleaning by a skin. Check integrity of teeths of a wreath. Put a flywheel on a flat surface and check plane deformation by means of calibre.
2. Clear and check a condition of the plane of the socket of a flywheel and the crankshaft. If it is revealed that the back epiploon of the crankshaft leaks before establishing a flywheel (a leading disk of the hydrotransformer) replace an epiploon (see subsection 3.1.1.15).
3. Establish a flywheel (a leading disk of the hydrotransformer) on the crankshaft. Combine the labels put at removal of a flywheel. Keep in mind that the part of cars on a flywheel has adjusting pins or openings under the adjusting bolts located out of a contour on which the main bolts of fastening settle down. Before a wraparound of bolts grease carvings with fixing structure.
4. Fix a flywheel a screw-driver for a gear wreath and tighten fastening bolts with the set moment. Tighten opposite bolts. A final inhaling execute for three-four stages.
5. Other operations on assembly are carried out upside-down.