Toyota Corolla

1992-1998 of release

Repair and car operation



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross-section stability (a forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and nave bearing (a forward wheel)
   10.9. Stabilizer of cross-section stability (a back suspension bracket) and plug
   10.10. Rack of a suspension bracket (back)
   10.11. Longitudinal draft
   10.12. Cross-section drafts of a suspension bracket
   10.13. Nave and bearing (a back wheel)
   10.14. Arm of a nave of a back wheel
   10.15. Steering
   10.16. Steering wheel
   10.17. Tips of steering drafts
   10.18. Steering transfer
   10.19. Pump of system of strengthening of a steering
   10.20. System of strengthening of a steering
   10.21. Wheels and tires
   10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment



10.10. Rack of a suspension bracket (back)

GENERAL INFORMATION

The correct provision of a support at assembly of a rack of a back suspension bracket
Establish a rack support so that its flat party looked forward and that fastening for an arm of a nave was in 5 ° from the distance middle between support openings.

1. Rack support

2. Fastening for a nave arm

Removal

PERFORMANCE ORDER
1. On models with a uniform back of a back seat, remove a back of a back seat; on models with separate backs of a back seat, remove all backs; on models with the Versatile person type body, remove a casing of the top fastening of a rack of a back suspension bracket (plastic a panel / cap on the lateral panel of furnish which fastens one screw) (see subsection 11.18).
2. Turn off nuts of fastening of a back wheel, lift a back part of the car and establish it on support. Remove a wheel.
3. Remove a clip (it is specified by an arrow), remove a brake hose from an arm on a rack of a back suspension bracket and stretch hose fastening through an opening in an arm. If on the car the ABS system is established, remove a wire of the sensor of speed of rotation of a wheel from a suspension bracket rack.
4. Remove connecting draft of the stabilizer of cross-section stability from a rack.
5. Establish a jack under a nave arm.
6. Turn off fastening nuts (are specified by shooters) a nave arm to a rack of a suspension bracket and beat out bolts by means of a hammer and a small beard.
7. Turn off three nuts (are specified by shooters) top fastening of a rack to a body.
8. Lower a nave arm together with a jack and get two bolts of fastening of an arm of a nave to a suspension bracket rack.
9. Remove a rack.

Check

PERFORMANCE ORDER
1. At check of a rack of a suspension bracket be guided by instructions (see subsection 10.3).
2. If the rack is necessary for disassembling for spring or shock-absorber replacement, be guided by instructions (see subsection 10.3).
3. At rack assembly, check, that the support of a rack was established how is shown on an illustration (see fig. The correct provision of a support at assembly of a rack of a back suspension bracket).

Installation

PERFORMANCE ORDER
1. Establish a rack under a wing of the car and insert bolts of the top fastening into body openings. Establish nuts, but do not twist them while up to the end.
2. Establish a nave arm on a rack, insert fixing bolts and put the clamps till the demanded moment of an inhaling specified in the section of technical characteristics at the beginning of this chapter.
3. Establish connecting draft of the stabilizer of cross-section stability on a rack arm.
4. Establish a brake hose on an arm of a rack and fix it by means of a clip. If on the car the ABS system is established, establish a wire of the sensor of speed of rotation of a wheel on a rack.
5. Establish a wheel and nuts. Lower the car on the earth and zatyanitegayka till the demanded moment of an inhaling specified in the section of technical characteristics at the beginning of this chapter.
6. Tighten three nuts of the top fastening of a rack of a suspension bracket till the demanded moment of an inhaling specified in the section of technical characteristics at the beginning of this chapter.
7. Repeat operations for the second rack, since removal (see point 2.).
8. Establish into place a back seat, a back or backs of a back seat or a casing of the top fastening of a rack of a back suspension bracket (see subsection 11.18).