Toyota Corolla

1992-1998 of release

Repair and car operation



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross-section stability (a forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and nave bearing (a forward wheel)
   10.9. Stabilizer of cross-section stability (a back suspension bracket) and plug
   10.10. Rack of a suspension bracket (back)
   10.11. Longitudinal draft
   10.12. Cross-section drafts of a suspension bracket
   10.13. Nave and bearing (a back wheel)
   10.14. Arm of a nave of a back wheel
   10.15. Steering
   10.16. Steering wheel
   10.17. Tips of steering drafts
   10.18. Steering transfer
   10.19. Pump of system of strengthening of a steering
   10.20. System of strengthening of a steering
   10.21. Wheels and tires
   10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment



10.7. Rotary fist and nave

GENERAL INFORMATION

Prevention

The dust formed as a result of wear of brake shoes, contains the asbestos which is hazardous to health. It is forbidden to use solvents on the basis of gasoline for cleaning of the mechanism of brakes. Use only alcohol or a special cleaner for the mechanism of brakes.


Removal

PERFORMANCE ORDER
1. Turn off nuts of fastening of a wheel, lift the car and establish it on support. Remove a wheel.
2. Get adjustable to the check and remove a cap of a nut of fastening of a semi-axis.
3. Turn off and remove a nut of fastening of a semi-axis and a washer. In order that the nave did not rotate, insert ломик between two bolts of fastening of a wheel and establish it so that the end ломика rested against the earth or the floor panel.
4. To get a semi-axis from шлицов naves, strike on the shaft end with a hammer with a brass head or use to copper small beards.
Prevention

Do not try while get the semi-axis end from a nave. If you make too big effort a semi-axis, you can damage it or a transmission.


5. Remove a brake support (see subsection 9.6) and a brake disk (see subsection 9.7), remove a brake hose from a suspension bracket rack.
6. If on the car the ABS system is established, disconnect and remove the sensor of speed of rotation of a wheel.
7. Turn off, but do not remove nuts and bolts, fastenings of a rotary fist to a suspension bracket rack (see subsection 10.2).
8. Remove the end of steering draft from the lever of a rotary fist (see subsection 10.17).
9. Turn off a bolt and nuts of fastening of the spherical hinge to the suspension bracket lever.
10. Get a semi-axis from a nave and suspend the semi-axis end on a wire.
11. By means of the tool for division of spherical hinges or a small stripper, remove the spherical hinge from a rotary fist.
12. Now it is possible to remove bolts of fastening of a rotary fist to a suspension bracket rack.
13. Accurately remove a rotary fist from a suspension bracket rack.

Installation

PERFORMANCE ORDER
1. Establish a rotary fist and a nave into place, having inserted a semi-axis into a nave.
2. Establish a rotary fist on a rack, insert bolts and acquire a nut, do not tighten while a nut up to the end.
3. If you removed the spherical hinge from an old rotary fist for installation on a new rotary fist, establish the hinge and twirl a nut of fastening of the hinge till the demanded moment of an inhaling (see subsection 10.1).
4. Establish the spherical hinge on the suspension bracket lever (see subsection 10.5), but do not tighten while a bolt and fixing nuts.
5. Establish steering draft on the lever of a rotary fist (see subsection 10.17). Put the clamps fastenings of a rotary fist to a suspension bracket rack, a bolt and nuts of fastening of the spherical hinge to the lever a suspension bracket and a nut of fastening of steering draft till the demanded moments of an inhaling (see subsection 10.1).
6. Establish a brake disk on a nave and establish a brake support, being guided by the instructions provided in the corresponding chapter.
7. Establish a nut of fastening of a semi-axis and tighten it till the demanded moment of an inhaling (see subsection 10.1).
8. Establish a wheel and acquire a nut of fastening of a wheel.
9. Lower the car on the earth and tighten nuts of fastening of a wheel till the demanded moment of an inhaling (see subsection 10.1).
10. Address to experts for check and if it is necessary, adjustments of installation of forward wheels.
13. Accurately remove a rotary fist from a suspension bracket rack.