Toyota Corolla

1992-1998 of release

Repair and car operation

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross-section stability (a forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and nave bearing (a forward wheel)
   10.9. Stabilizer of cross-section stability (a back suspension bracket) and plug
   10.10. Rack of a suspension bracket (back)
   10.11. Longitudinal draft
   10.12. Cross-section drafts of a suspension bracket
   10.13. Nave and bearing (a back wheel)
   10.14. Arm of a nave of a back wheel
   10.15. Steering
   10.16. Steering wheel
   10.17. Tips of steering drafts
   10.18. Steering transfer
   10.19. Pump of system of strengthening of a steering
   10.20. System of strengthening of a steering
   10.21. Wheels and tires
   10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment

10.12. Cross-section drafts of a suspension bracket

GENERAL INFORMATION

Drafts and cross-piece of a back suspension bracket

1. Suspension bracket cross-piece
2. Cross-section draft of a suspension bracket of N2

3. Cross-section draft of a suspension bracket of N1
4. Longitudinal draft

Removal

PERFORMANCE ORDER

1. Turn off nuts of fastening of a back wheel, lift a back part of the car and establish it on support.
2. Block forward wheels and remove a back wheel.
Cross-section draft of N2
3. If on the car the valve of restriction of pressure in a contour of the back brakes is established, sensitive to car loading – turn off a lock-nut, a fixing bottom spring of the valve to the right cross-section draft of N2. Try not to braid the adjusting nut, established is slightly higher. It is recommended to mark an adjusting nut and a carving of fastening of a spring with quick-drying paint in order that then it was possible to establish them in initial situation.
	4. Remove a nut and a washer from the external end of the cross-section draft, fixing it to an arm of a nave and remove a bolt (if you remove only draft of N2, it is not necessary to get a bolt).
	5. Turn off and remove a nut and a washer from the internal end of the cross-section draft, fixing it to a suspension bracket cross-piece.
6. Remove cross-section draft of N2. Prevention Do not turn off a lock-nut and do not rotate an adjusting coupler; if you turn off a coupler, it will change a convergence of back wheels.
Cross-section draft of N1
7. Turn off a nut and a bolt, drafts fixing the internal end. Also, turn off a nut and a bolt, bent for fixing the external end to a nave arm. Remove the central section of an exhaust pipe and isolation of an exhaust pipe (see subsection 5.13). If on the car the valve of restriction of pressure in a contour of the back brakes, sensitive to car loading is established, disconnect fastening of the bottom spring (see point 3).
8. Establish a jack under a cross-piece of a back suspension bracket. Turn off four bolts, fixing a cross-piece (see fig. Drafts and cross-piece of a back suspension bracket). Lower a cross-piece so that it was possible to get the long through bolt, fixing cross-section drafts.
9. Turn off and remove a bolt and a nut of fastening of forward cross-section bent for to an arm of a nave of a back wheel.
10. Remove a nut and a bolt, fixing forward cross-section bent for to a suspension bracket cross-piece.
11. Remove cross-section draft of N1.