Toyota Corolla

1992-1998 of release

Repair and car operation


Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross-section stability (a forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and nave bearing (a forward wheel)
   10.9. Stabilizer of cross-section stability (a back suspension bracket) and plug
   10.10. Rack of a suspension bracket (back)
   10.11. Longitudinal draft
   10.12. Cross-section drafts of a suspension bracket
   10.13. Nave and bearing (a back wheel)
   10.14. Arm of a nave of a back wheel
   10.15. Steering
   10.16. Steering wheel
   10.17. Tips of steering drafts
   10.18. Steering transfer
   10.19. Pump of system of strengthening of a steering
   10.20. System of strengthening of a steering
   10.21. Wheels and tires
   10.22. Adjustment of corners of installation of wheels
+ 11. Body
+ 12. Electric equipment


We are a video production service company in Cyprus

10.14. Arm of a nave of a back wheel
GENERAL INFORMATION
Prevention

The dust formed as a result of wear of brake shoes, contains the asbestos which is hazardous to health. It is forbidden to use solvents on the basis of gasoline for cleaning of the mechanism of brakes. Use only a special cleaner for the mechanism of brakes.

Removal
PERFORMANCE ORDER
1. Turn off nuts of fastening of a wheel, lift the car and establish it on support. Block forward wheels and remove a back wheel.
2. Remove a brake drum (on models with back drum-type brakes) or remove a brake disk and a brake support (on models with back disk brakes).
3. Remove a brake hose from an arm on a suspension bracket rack (the clip – is specified by an arrow).
4. Remove a nave of a wheel and the bearing (see subsection 10.13).
5. Remove a guard of a back brake and the brake mechanism (on models with back drum-type brakes). It is not necessary to assort the mechanism of brakes or to disconnect a rope of the hand brake. Suspend a guard together with the mechanism of a back brake on a suspension bracket spring by means of a wire. Do not bend a brake tube.
6. On models from ABS, remove the sensor of speed of rotation of a wheel from a nave arm (see fig. Elements of an arm of a nave, a nave and the bearing of a nave of a back wheel (model with drum-type brakes)).
7. Turn off, but do not remove fastening bolts (are specified by shooters) nave arm to a suspension bracket rack.
8. Turn off and remove a bolt, a nut and washers (naves fixing an arm to cross-section levers of a suspension bracket are specified by shooters), and remove a bolt of fastening of an arm of a nave to longitudinal draft of a suspension bracket.
9. Remove the turned-off bolts of fastening of an arm of a nave to a suspension bracket rack, supporting an arm that it did not fall, and remove a nave arm from a suspension bracket rack.

Installation
PERFORMANCE ORDER
1. Examine the plug of an arm of a nave on existence of cracks, deformation or wear tracks. If it is worn-out, give an arm to a repair truck for replacement.
2. Establish a nave arm on a suspension bracket rack, having combined openings for two fixing bolts. Insert two fixing bolts and tighten them till the demanded moment of an inhaling (see subsection 10.1).
3. Establish a bolt of fastening of cross-section levers of a suspension bracket to a nave arm, put on washers and twirl a nut. Do not twist while a nut up to the end.
4. Establish longitudinal draft on an arm of a nave and tighten fingers a fixing nut and a bolt.
5. Establish a jack under an arm of a nave and lift it on such height on which it approximately is when the car costs on wheels.
6. Tighten a nut and a bolt of fastening of cross-section drafts of a suspension bracket till the demanded moment of an inhaling (see subsection 10.1). Clean a jack from under a nave arm.
7. On models from ABS, establish the sensor of speed of rotation of a wheel on a nave arm.
8. Establish a guard of a back brake on a nave arm, establish a nave and tighten four bolts of fastening of a nave till the demanded moment of an inhaling (see subsection 10.1).
9. Establish a brake tube on an arm of a rack of a suspension bracket and fix it by means of a clip. Check, that the hose was not overwound.
10. Establish a brake drum (see subsection 9.8) or a brake disk (see subsection 9.7) and a support (see subsection 9.6).
11. Establish a wheel and nuts of fastening of a wheel.
12. Lower the car on the earth and tighten nuts of fastening of a wheel till the demanded moment of an inhaling (see subsection 10.1).