Toyota Corolla

1992-1998 of release

Repair and car operation

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines
   - 3.2. Diesel engine
      3.2.1. Specifications
      3.2.2. Replacement of a gear belt
      3.2.3. Removal of a head of cylinders
      3.2.4. Dismantling of a head of cylinders
      3.2.5. Partition of a head of cylinders
      3.2.6. Assembly of a head of the block of cylinders
      3.2.7. Installation of a head of cylinders
      3.2.8. Check and adjustment of gaps of valves
      3.2.9. Check of a compression of cylinders
      3.2.10. Pistons and rods
      3.2.11. Measurement of cylinders
      3.2.12. Assembly of pistons and rods
      3.2.13. Installation of pistons and rods
      3.2.14. Cranked shaft and flywheel
      + 3.2.15. Cooling system
      + 3.2.16. Greasing system
      3.2.17. Device of injection of diesel fuel
      3.2.18. Car operation on diesel fuel
      3.2.19. Fuel filter
      3.2.20. Fuel pump of a high pressure
      3.2.21. Nozzles
      3.2.22. Glow plugs
      3.2.23. Adjustment of a mode of idling
      3.2.24. Adjustment of the maximum turns
      + 3.2.25. Good advice to owners of the diesel engine
   + 3.3. Engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment

3.2.3. Removal of a head of cylinders

GENERAL INFORMATION

Assembly drawing of a head of cylinders

1. Cover of a head of cylinders
2. Cover laying
3. Cover of the bearing of a rasproyedelitelny shaft
4. Compensatory washer
5. Valve pusher
6. Valve crackers
7. Cup of a spring of the valve
8. Valve spring
9. Maslootrazhatelny cap of a core of the valve
10. Emphasis of a spring of the valve
11. Directing the valve
12. Camshaft
13. Bolt of a head of cylinders
14. Head of cylinders
15. Condensing встака
16. Union of connection of a head of cylinders
17. Laying of a head of cylinders

18. Final collector
19. Collector laying
20. Flange of an epiploon of a camshaft
21. Camshaft cogwheel
22. Top cover of a gear belt
23. Naprvlyayushchy roller of a gear belt
24. Returnable spring
25. Compensatory washer
26. Valve saddle
27. Valve
28. Returnable toprlivny tube
29. Nozzle
30. Nozzle nest
31. Epiploon
32. Average cover of a gear belt
33. Rubber tip
34. That tire
35. Glow plug
36. Collector laying
37. Inlet collector

Order of an inhaling of bolts of a head of cylinders

Below the description of removal and installation of a head of cylinders without engine removal is provided.

PERFORMANCE ORDER

1. Disconnect the accumulator.

2. Merge cooling liquid.

3. Remove tubes of nozzles, nozzles and a tube of supply of fuel.

4. Disconnect from an inlet collector a food wire. Remove from candles of 4 rubber tips, unscrew 4 nuts, remove that tire and turn out four glow plugs. Fastening of candles is shown in the right part fig. Assembly drawing of a head of cylinders.

5. Remove a gear belt as it was described in the previous chapter. Remove also a camshaft cogwheel.

6. Disconnect the mechanism of a cable of gas.

7. Lift the receiver plum of cooling liquid and a heater tube. Thus also the bracket for an engine raising is released. Under a flange of a tube there is a laying. Disconnect since one end a hose.

8. Unscrew from the forward party of the engine an average cover (32) gear belts on fig. Assembly drawing of a head of cylinders.

9. Remove six nuts and sealing washers of a cover of a head of cylinders and uncover with laying.

10. Remove a forward elevating bracket of the engine.

11. Evenly cross-wise in the sequence specified fig. An order of an inhaling of bolts of a head of cylinders, unscrew eighteen bolts of a head of cylinders.

12. Lift a head of cylinders from pins in a head of cylinders and put it on a workbench. Strong sat down head of cylinders can be separated from the block of cylinders by means of a screw-driver inserted between a head of cylinders and a ledge of the block of cylinders. Do not damage thus a head of cylinders. Remove traces of old consolidation. Do not allow hit of the remains of old laying in the block of cylinders.