Toyota Corolla - 1. Maintenance instruction 1.2. Codes of models 1.3. Control panel + 1.4. Combination of devices + 1.5. Governing bodies and instrumentations - 1.6. Start-up of the engine and driving 1.6.1. Check before engine start-up 1.6.2. Check after engine start-up 1.6.3. Driving receptions + 1.6.4. Trailer towage 1.6.5. Actions at refusal of start-up of the engine 1.6.6. Obligatory set of tools and spare wheel 1.6.7. Wheel replacement 1.6.8. Car towage 1.6.9. Motor compartment 1.6.10. Arrangement of safety locks 1.6.11. Check of level of oil in the engine 1.6.12. Choice of brand of oil 1.6.13. Check of level of cooling liquid 1.6.14. Composition of cooling liquid 1.6.15. Pressure check in tires 1.6.16. Replacement of tires 1.6.17. Shift of wheels 1.6.18. Installation of winter tires and chains 1.6.19. Precautionary measures for cast aluminum disks 1.6.20. Check of an external condition of the battery 1.6.21. Check of level of electrolit 1.6.22. Battery charging 1.6.23. Check and replacement of safety locks + 1.6.24. Replacement of lamps 1.7. Specifications 1.8. Adjusting data, refueling capacities and liquids + 1.9. Possible malfunctions + 2. Maintenance + 3. Engines + 4. Systems of cooling, heating + 5. Fuel, exhaust systems + 6. System of decrease in toxicity + 7. Transmissions + 8. Coupling and semi-axes + 9. Brake system + 10. Suspension bracket and steering + 11. Body + 12. Electric equipment
|
Before engine start-up
PERFORMANCE ORDER |
1. Examine a platform near the car. |
2. Take a place, adjust the provision of a seat, a head restraint and a wheel tilt angle. |
3. Adjust the provision of rear-view mirrors. |
4. Close all doors. |
5. Be fastened by a belt. |
|
Before starter inclusion
PERFORMANCE ORDER |
1. Put the car on the hand brake. Switch off everything unnecessary consumers and lighting devices. |
2. On cars from mechanical KP press a coupling pedal to a floor and put KP control lever in neutral situation. Hold a pedal pressed before engine start. |
3. On cars with automatic transmission transfer the selector lever to R.Esli's position it is necessary to start the decayed engine during movement, transfer the lever to situation N. If the lever is in any situation corresponding to movement, the safety device will prevent starter inclusion. |
4. Only on cars with automatic transmission press a brake pedal to the full and hold prior to the beginning of movement. |
|
Engine start
Prevention
Period of operation of a starter at start should not exceed 15 pages. Otherwise the starter and cables overheat.
Be not dispersed sharply on the cold engine.
Еспи the engine often глохнет or is badly started, immediately check an engine condition.
MODEL 2Е
PERFORMANCE ORDER |
1. Follow the instructions stated above. |
Start under normal conditions, engine cold |
2. Press a butterfly valve pedal to the full and release. The system of increase of turns of idling and the automatic starting arrangement thus join. |
3. Clean a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after engine start. |
4. Let's get warm to the engine during 10 with then the car is ready to movement. |
Start at negative temperature or after parking within several days |
5. Before inclusion of a starter press 2–3 times a butterfly valve pedal to the full and release. Thus there is a mix enrichment at engine start-up. |
6. Clean a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after engine start. |
7. Let's work to the engine during 30 with, quickly press a pedal of a butterfly valve and lower idling turns. |
8. Let's get warm to the engine within several minutes then the car is ready to movement. |
Start-up of the warm engine |
9. Press a butterfly valve pedal approximately on a half of a course and include a starter, having turned the ignition key in the situation START. Release a key and a butterfly valve pedal after engine start. |
Start-up of the hot engine |
10. Press a butterfly valve pedal to the full and include a starter, having turned the ignition key in the situation START. Release a key and a butterfly valve pedal after engine start. A pedal not to press any more. |
Start-up of the decayed engine |
11. Repeat described above action depending on engine temperature. |
Refusal of start-up of the engine |
12. Be guided by the description in subsection 1.6.5. |
|
MODEL 4E-FE, 4A-FE and 7A-FE (FOR the CARS SOLD IN GERMANY)
Cars are equipped with multichannel system of direct injection of fuel (or consecutive injection) which automatically prepares a mix necessary for start-up of the engine. Irrespective of a thermal condition the engine is started as follows.
PERFORMANCE ORDER |
1. Follow the instructions stated above. |
Start under normal conditions |
2. Clean a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after engine start. |
3. To warm up the engine only at a trip, but not idling. Move with moderate speed until the temperature of cooling liquid will not raise to an operating level. |
4. If the engine decayed, start it, having repeated start procedure in normal conditions. |
At refusal of start-up of the engine |
5. Be guided by the description in subsection 1.6.5. |
|
MODEL 4E-FE, 4A-FE and 7A-FE (FOR ALL CARS, EXCEPT INTENDED FOR GERMANY)
Cars are equipped with multichannel system of direct injection of fuel (or consecutive injection) which automatically prepares a mix necessary for start-up of the engine. Irrespective of a thermal condition the engine is started as follows.
PERFORMANCE ORDER |
1. Follow the instructions stated above. |
Start under normal conditions |
2. Clean a foot from a pedal of a butterfly valve and include a starter, having turned the ignition key in the situation START. Release a key after engine start. |
3. Let's get warm to the engine during 10 with then the car is ready to movement. |
4. In frosty conditions let's work to the engine within several minutes then the car is ready to movement. |
5. If the engine decayed, start it, having repeated start procedure in normal conditions. |
At refusal of start-up of the engine |
6. Be guided by the description in subsection 1.6.5. |
|
MODEL 2С (ON THE CARS INTENDED FOR GERMANY)
|
Control lamp of prestarting heating |
PERFORMANCE ORDER |
1. Follow the instructions stated above. |
Start under normal conditions, engine cold |
2. Turn the ignition key in the situation On, be convinced that the control lamp of prestarting heating lit up. Hold the ignition key in the situation On until the control lamp will not go out. |
3. Press a butterfly valve pedal to the full and include a starter, having turned the ignition key in the situation START. Clean a foot from a pedal of a butterfly valve and release a key after engine start. |
4. To warm up the engine only at a trip, but not idling. Move with moderate speed until the temperature of cooling liquid will not raise to an operating level. |
Start-up of the warm engine |
5. Press a butterfly valve pedal approximately on a half of a course and include a starter, having turned the ignition key in the situation START. Release a key and a butterfly valve pedal after engine start. |
6. If the engine is not started, execute actions for start-up in normal conditions. |
7. If the engine decayed, start it, having repeated described above procedure depending on a thermal condition of the engine. |
At refusal of start-up of the engine |
8. Be guided by the description in subsection 1.6.5. |
9. Coupling guard. |
10. The bottom bolts of fastening of a case of coupling to the block of cylinders. |
|
MODEL 2С (ON ALL CARS, KROM INTENDED FOR GERMANY)
|
Control Pampas of prestarting heating |
PERFORMANCE ORDER |
1. Follow the instructions stated above. |
Start under normal conditions, engine cold |
2. Turn the ignition key in the situation On, be convinced that the control lamp of prestarting heating lit up. Hold the ignition key in the situation On until the control lamp will not go out. |
3. Press a butterfly valve pedal to the full and include a starter, having turned the ignition key in the situation START. Clean a foot from a pedal of a butterfly valve and release a key after engine start. |
4. Let's get warm to the engine during 10 with then the car is ready to movement. |
5. In frosty conditions let's work to the engine within several minutes then the car is ready to movement. |
Start-up of the warm engine |
6. Press a butterfly valve pedal approximately on a half of a course and include a starter, having turned the ignition key in the situation START. Release a key and a butterfly valve pedal after engine start. |
7. If the engine is not started, execute actions for start-up in normal conditions. |
8. If the engine decayed, start it, having repeated described above procedure depending on a thermal condition of the engine. |
At refusal of start-up of the engine |
9. Be guided by the description in subsection 1.6.5. |
10. The bottom bolts of fastening of a case of coupling to the block of cylinders. |
|
Car check before a trip
Before a trip it is recommended to examine the car. Having spent some minutes, you will provide a safe and pleasant trip. Here only thorough acquaintance to own car and attentiveness is required. |
|