Toyota Corolla

1992-1998 of release

Repair and car operation


Toyota Corolla
- 1. Maintenance instruction
   1.2. Codes of models
   1.3. Control panel
   + 1.4. Combination of devices
   + 1.5. Governing bodies and instrumentations
   - 1.6. Start-up of the engine and driving
      1.6.1. Check before engine start-up
      1.6.2. Check after engine start-up
      1.6.3. Driving receptions
      + 1.6.4. Trailer towage
      1.6.5. Actions at refusal of start-up of the engine
      1.6.6. Obligatory set of tools and spare wheel
      1.6.7. Wheel replacement
      1.6.8. Car towage
      1.6.9. Motor compartment
      1.6.10. Arrangement of safety locks
      1.6.11. Check of level of oil in the engine
      1.6.12. Choice of brand of oil
      1.6.13. Check of level of cooling liquid
      1.6.14. Composition of cooling liquid
      1.6.15. Pressure check in tires
      1.6.16. Replacement of tires
      1.6.17. Shift of wheels
      1.6.18. Installation of winter tires and chains
      1.6.19. Precautionary measures for cast aluminum disks
      1.6.20. Check of an external condition of the battery
      1.6.21. Check of level of electrolit
      1.6.22. Battery charging
      1.6.23. Check and replacement of safety locks
      + 1.6.24. Replacement of lamps
   1.7. Specifications
   1.8. Adjusting data, refueling capacities and liquids
   + 1.9. Possible malfunctions
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and semi-axes
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment



1.6.7. Wheel replacement
PERFORMANCE ORDER
1. To prevent movement of the car lifted on a jack, block a wheel diagonalno opposite to the punctured. Enclose blocks in front of a forward wheel and behind the back.
2. Hook a cap a slanted part of a stripper of a cap.
On cars with the petrol engine as a stripper it is possible to use the handle of a candle key.
Prevention

It is not allowed to remove a cap manually. At the address with a cap it is necessary to observe extra care to avoid traumas.
3. Before lifting of the car it is necessary to weaken an inhaling of nuts of wheels. For this purpose turn on a nut counter-clockwise. For receiving the maximum effort have a key so that the handle was from the right party. At an otvorachivaniye undertake handle edge, watch that the key did not slide off a nut. Nuts are necessary for weakening only on a half of turn, completely not to turn on.
4. A jack to establish only under the places specified an illustrations. The platform of installation of a jack should be equal and firm.
5. Be convinced that in salon there are no passengers, and lift the car so that it was possible to establish a spare wheel. Remember that for installation of a spare wheel the car should be lifted above, than at removal of the punctured.
6. For lifting insert the jack handle into an earring and rotate clockwise. At the very beginning of lifting be once again convinced of correctness of installation of a jack.
7. Unscrew nuts and remove the punctured wheel.
8. Drive a spare wheel and will expose so that openings in a disk were opposite to hairpins.
9. Lift a wheel and dress on the top hairpin. Having shaken, dress a wheel on other hairpins.
10. Before establishing a wheel, remove corrosion traces on places of a prileganiye of a disk with a metal brush. The insufficient prileganiye of a disk can lead to an otvorachivaniye of nuts and a wheel separation when driving. Therefore through each 1600 km check an inhaling of nuts of wheels.
11. Screw nuts of wheels (inside a konusny part), tighten by hand. Wring out a wheel and at possibility tighten nuts.
12. Lower the car and tighten nuts. For this purpose rotate the jack handle counter-clockwise. For an inhaling of nuts use only a key for wheel nuts. Tighten nuts manually, use of extraneous means and the tools changing the moment of an inhaling (a hammer, pipes, etc. and also to hold out nuts, resting against a key a foot), is not allowed.

13. Be convinced that the key is reliably dressed on a nut. Wrap nuts gradually in an order specified an illustrations. Repeating sequence of an inhaling, finally tighten nuts.
14. Establish a cap in a place and slightly пристукните a foot before click.
15. After change of a wheel check pressure in the tire of the established wheel. Adjust pressure according to the norms specified regarding 8.
16. If pressure is lower nominal, on small speed reach the next workshop and pump up the tire. Do not forget to wrap a gate cap, otherwise dirt can get to a zolotnik and cause a leak. In a case утери a cap as soon as possible get and establish.
17. Lay on the places a jack, the damaged wheel and the tool. As soon as possible tighten wheel nuts a dinamometrichesky natural the set moment, repair the damaged tire.






QX4.ONLINE
S40.ONLINE
A-8.ONLINE
W124.ONLINE
RX300.ONLINE
W140.ONLINE
B3-B4.SPACE
B3B4.SPACE
A-8.SPACE